Hard to keep up with this thread. New posts and reading from the beginning. Lol made it to post 660 so far.whew
Sent from my Nexus 6P using Tapatalk
I just jumped in the middle and went from there! Now waiting for @troydestroy to let us know then the plugs are ready I've been using my BB unplugged as it were, but thanks to the folks here I knew to put a bit of lint free paper towel behind the tankHard to keep up with this thread. New posts and reading from the beginning. Lol made it to post 660 so far.whew
Sent from my Nexus 6P using Tapatalk
Yea I figured what better than inside information. I can't trust anyone else to tell me what's good. The just wanna sell it. Enough reading and I know what I need to research instead of a broad spectrum. Plus it was definitely worth the read back to see some of the panels and buttons.I just jumped in the middle and went from there! Now waiting for @troydestroy to let us know then the plugs are ready I've been using my BB unplugged as it were, but thanks to the folks here I knew to put a bit of lint free paper towel behind the tank
Wolverine! Awesome!Been super busy with teaching this spring but thought I’d say hello and include a little update.
Still in a long term relationship with my MF Bridge (Vaporesso EUC .5 Clapton’s)
Just met my new JMK stainless steel threaded drip tip today. Super nice though.
F5X1 Custom Panels (My design plus some discussion for windows)
All Star Custom Creations Condensation Plug (didn’t realize how much it mattered till we entered each other’s life.
Only thing that could replace my daily driver would be a full ultem billet box and even then we would have to discuss how both would share time with me.
Thanks for your input. Maybe there's still hope that one day I will be satisfied with mine.Interesting that a clone vapeshell could be that much different from the authentic given that the overall design is rather simple. Personally, I have not encountered a single issue with mine, wicks very consistently, never dry and I never have flooding, or any overflow from the 510 for that matter. To me, the Atmizoo Vapeshell is basically the Kayfun prime in a pod system. Again my only gripe is the process of wick/coil changing which requires a few extra steps, but fortunately, its something I don't need to do often since the juice I use is mostly unflavored.
Two friends of mine also use the Atimizoo VS, one wide open and another uses my leftover MTL disc that he drilled out to same diameter as the one I'm currently using. The wide open build uses one of the lower resistance fancy coils, the other is built in somewhere between mine and the wide open draw, neither of them have wicking or build issues as well.
So something I noticed about the SXK VapeShell is that there doesn't seem to be enough clearance between the bottom of the shell and the bottom of the Boro.
I notice air bubbles struggling to come out of the juice flow holes and if I tilt the BB they seem to come free.
I really can't think of a solution to this other than getting a tighter draw with either the MTL inserts (who knows if the authentic fit as SXK doesn't offer them yet) or some sort of airflow restricting condensation plug.
Also I'm using 60vg/40pg juice so viscosity shouldn't be an issue.
Hope this helps those struggling a bit somehow.
Sent from my SM-G965U using Tapatalk
I'd say get the VapeShell authentic, get pissed with it, and sell it to meI like the looks of the VS... the Deck...but even if I was able to grab an authentic for <$70 I wouldn't. It seems one of those RBAs that is either hit or miss with a lot of folk, and I know I'd be that fucker who it just wouldn't rock about with it. Same with the Insider...its a really good vape, truly...just not my vape.
Exocet though...that has me happy...dog eared silly looking... fuck it, dont care... its covered by panels I didn't have to muck about making coils trying to find a vape... first coil in and its rocking.
I still think that the VS has a major design flaw with the holes being at the bottom...could of achieved the same with the holes on the sides, the aesthetics would of been the same.. juice flow less restricted.
So something I noticed about the SXK VapeShell is that there doesn't seem to be enough clearance between the bottom of the shell and the bottom of the Boro....
...Exocet though...that has me happy...dog eared silly looking... fuck it, dont care... its covered by panels I didn't have to muck about making coils trying to find a vape... first coil in and its rocking...
One of the things I really like about the Exocet is that the wicking is very very forgiving.
Geekay has a video tutorial on the Exocet, Insider, and Bastard Coil attys:
Exocet:
Insider:
Bastard:
One thing I found with regard to the Exocet is that if you are using a thinner dia coil, and therefore thinner amt of cotton, it is almost crucial to slightly rotate the barrel about 5 degrees, so as to sort of pinch the wicks at an almost 90 degree angle to the center of the coil itself, and this helps with flooding and gurgling.
After you rotate the barrel, then you press it down over the o-ring.
With a 2.5mm or 3mm build and wicked tight, this may not be a concern, but with 2mm coils and smaller, I found it absolutely necessary otherwise the coil gets flooded rather easily, even with 100%VG juice.
This works because the rotation of the barrel helps to seal off the juice slots once the cotton expands.
Also Jai Haze has a tutorial for the VapeShell:
Thanks... Playing with coils today in the Exocet...
Now if only someone would buy my Insider so I can buy the Doggy lol
Awesome, thanks
Awesome, thanks
I got that, but that doesn't stop me from thanking youLittle clarification... it was shipped to me today!
Although I am sure you got that by the Chula Vista listed...
Probably still faster than Slowtech!long way to go
May 30, 2018, 6:50 am
Departed USPS Facility
WEST VALLEY CITY, UT 84119
Your item departed our USPS facility in WEST VALLEY CITY, UT 84119 on May 30, 2018 at 6:50 am. The item is currently in transit to the destination.
May 30, 2018, 2:10 am
Arrived at USPS Facility
WEST VALLEY CITY, UT 84119
May 30, 2018, 1:59 am
Departed USPS Regional Facility
SALT LAKE CITY UT NETWORK DISTRIBUTION CENTER
May 29, 2018, 7:08 pm
Arrived at USPS Regional Facility
SALT LAKE CITY UT NETWORK DISTRIBUTION CENTER
May 29, 2018, 5:53 pm
Accepted at USPS Origin Facility
OGDEN, UT 84402
May 28, 2018, 8:12 am
Shipping Label Created, USPS Awaiting Item
OGDEN, UT 84402
About the same for 1st class from USAProbably still faster than Slowtech!
Sent from my SM-G965U using Tapatalk
BoooooooAbout the same for 1st class from USA
Not if you're like me! Ordered May 9th from FT....Still not here, They are supposed to track package now. We shall see....About the same for 1st class from USA
Didn't someone just get one a while back they talked about selling? I can never remember who but.
Sent from my Nexus 6P using Tapatalk
Gotta be stealthy when your parents told you not to vape in the house...So I am cruising ole FaceSlut and I come across this...
View attachment 112590
I get the matchy... truly
Maybe at home its stealth :Shrug
Rocket propelled grenade?I sold my GooberFet and bought my RPG with the money I got for it.
Rocket propelled grenade?
Sent from my Nexus 6P using Tapatalk
Can you imagine going thru a security point at the airport and telling them to please be careful and not scratch your RPG?Rocket propelled grenade?
Sent from my Nexus 6P using Tapatalk
Has anybody ordered the YFTK DNA 60 BB yet?
Just ordered one from 3F. I was planning on ordering from FT, but 3F has the 24hr shipping status whereas FT was 7 business days. Hopefully I'll let you know in a couple of weeks.Has anybody ordered the YFTK DNA 60 BB yet?
The YFTK version is a DNA 60.isn't the sxk $20 cheaper? is there an issue with it
If rumors are right, the USB connection would be worth waiting for since you'd be able to use eScribe and load your own profiles.Just ordered one from 3F. I was planning on ordering from FT, but 3F has the 24hr shipping status whereas FT was 7 business days. Hopefully I'll let you know in a couple of weeks. The YFTK version is a DNA 60.
The SXK with the 70W Ares chip is $20 cheaper but the SXK DNA 60 version is $30ish dollars more.
Rumor has it that SXK is releasing a DNA 60 with a USB port in the button panel, but no one knows when it will be released and it will probably be sold at the $129 price point.
Sent from my SM-G965U using Tapatalk
Yes, I've seen these. Theres a group by on Facebook (or there was, dunno if still going)Just ordered one from 3F. I was planning on ordering from FT, but 3F has the 24hr shipping status whereas FT was 7 business days. Hopefully I'll let you know in a couple of weeks. The YFTK version is a DNA 60.
The SXK with the 70W Ares chip is $20 cheaper but the SXK DNA 60 version is $30ish dollars more.
Rumor has it that SXK is releasing a DNA 60 with a USB port in the button panel, but no one knows when it will be released and it will probably be sold at the $129 price point.
Sent from my SM-G965U using Tapatalk
Amen. All I want is to flip the screen lolYes, I've seen these. Theres a group by on Facebook (or there was, dunno if still going)
I've settled nicely with ka1 or SS in power mode. SS just pisses me off in TC...
Save me a couple MTL!@BrewBear and others...
The new DryPlugs are in
I think you MTL junkies will be very happy!
I'll post in the classifieds shortly, or feel free to PM me.
Doesn't it make sense to order at least a couple? I figure since you need to clean and soak the plug in alcohol, then wait for it to dry, you either have to wait or vapresso on something else. BTW, how often do you need to clean it up?
I want one of the Tweakings AFC plugs, but every place I've looked at is sold outI have 2, one from Troy and one from tweakings...I clean mine, then use a blow dryer or my plug in air duster and its dry in about 30 secs.
Sent from my iPhone using Tapatalk
I'd love to get your comparison with this one once you get the DryPlug!I manged to order one of these last week - http://www.svapolibero.it/shop/en/Billet-Box-Vapor/6112-AFC-PER-BILLET-BOX-by-Cra.html
But they're out of stock now as well !
I'd love to get your comparison with this one once you get the DryPlug!
I want one of the Tweakings AFC plugs, but every place I've looked at is sold out