Has anyone posted a picture of the NC with the upgrade? How much taller does it make it?
Sent from my SM-G360T using Tapatalk
Nice little tube, I put a heat sink on that makes it a bit taller.Duh, my fault.
Thanks! I expected it to be taller. Cool.
Sent from my SM-G360T using Tapatalk
I want someone to come out with a heatsinkless "heatsink" just a 510 connection. The upgrade for the NC is cool, and I got it, but it's a floating section not the solid connection I want. I want that thing to sit like I have a heatsink on it, but I don't need a heatsink as I don't vape to the point that I need that cooling gap between the mod and atty.Nice little tube, I put a heat sink on that makes it a bit taller.
Sent from my Nexus 6 using Tapatalk
Confused, the floating pin is the reason for the kit.I want someone to come out with a heatsinkless "heatsink" just a 510 connection. The upgrade for the NC is cool, and I got it, but it's a floating section not the solid connection I want. I want that thing to sit like I have a heatsink on it, but I don't need a heatsink as I don't vape to the point that I need that cooling gap between the mod and atty.
No absolutely, It's a great option, I just want a better one is what I'm saying. Not just for the NC, but for all mods I want that secure 510 adapter I described. In the end even with the adapter you still have a floating piece connecting to the battery, I'd prefer a solid one. Pin the battery, connect the atty, that kind of thing.Confused, the floating pin is the reason for the kit.
Sent from my Nexus 6 using Tapatalk
So you want a 510 deck with a heat sink built in? If so yes I very much agree, would love to see that myself.No absolutely, It's a great option, I just want a better one is what I'm saying. Not just for the NC, but for all mods I want that secure 510 adapter I described. In the end even with the adapter you still have a floating piece connecting to the battery, I'd prefer a solid one. Pin the battery, connect the atty, that kind of thing.
Yeah that was before getting it, just reading the specs it said floating, so I was expecting a loose piece just hanging out in there, not one with an o-ring that sits in there pretty firmly. It's actually pretty solid. Still would like that more universal adapter I'm talking about for other potential uses though.So you want a 510 deck with a heat sink built in? If so yes I very much agree, would love to see that myself.
Edit:
Reading your response again I still don't get it. With the deck on the upgrade kit, screw it on the Addy first before you screw it into the NC, it will sit flush. It is a solid floating pin
Sent from my Nexus 6 using Tapatalk
Understood and I agree.Yeah that was before getting it, just reading the specs it said floating, so I was expecting a loose piece just hanging out in there, not one with an o-ring that sits in there pretty firmly. It's actually pretty solid. Still would like that more universal adapter I'm talking about for other potential uses though.
10 amps?I'll take one of those Cricket bodies 18350 sized would be cool as well.
Yup, I have made a few 1Ω+ builds that actually work very well with a series mech, which would be plenty safe for 18350's, but I'd prefer the 18650s.No offense but I would disagree. It is series mod that would still fire at 7.4-8.4 Volt. I am positive there is plenty of coil configurations that would provide plenty of fire. 18650 cricket can be built below 3.5 Ohm but it's getting too hot for most people because of high voltage output. It would be smallest unregulated mechanical mod as well.
No offense but I would disagree. It is series mod that would still fire at 7.4-8.4 Volt. I am positive there is plenty of coil configurations that would provide plenty of fire. 18650 cricket can be built below 3.5 Ohm but it's getting too hot for most people because of high voltage output. It would be smallest unregulated mechanical mod as well.
Yup, I have made a few 1Ω+ builds that actually work very well with a series mech, which would be plenty safe for 18350's, but I'd prefer the 18650s.
It depends on the batteries you are using. Some batteries (like the Samsung 25Rs) can pulse nicely beyond their continuous discharge rating. Without knowing which batteries you're using or the complete specs of the Claptons, none of us can say that they're safe to vape on a Noisy Cricket.I have some SS claptons 26/30 from Advanced Vape Supply that are around .709 ohm each. Meaning duals would be around .34ohm do you think that would much for the noisy cricket?
James
Right now I'm runing dual coils that are kanthal an regular wrap 26 gauge that come out to about .72
You need to be familiar with Steam Engine if you're going to using a mech, ESPECIALLY with a series mod.They batteries are Sony VTC5 2600 the Claptons are the one in this link https://www.advancedvapesupply.com/...less-steel-clapton-coil-26g-or-28g-30g-or-32g, they're the 26g core, 30g wrap at 3mm diameter
Thank you, but that's probably not gonna happen. Ribbon is inherently much lower in resistance than round wire. The coils would have to be VERY wide to make them able to be used as a dual coil setup in a Noisy Cricket.I want a pair of framed staple coils for the noisy cricket
Unfortunately, right now I'm only offering SS316L for TC coils.Would it be possible for one set the alien coils to use nickel wrap preferably the set for the Boreas so I can use temp control?
The Polished coils are pretty easy to spec out for the NC.How would the single wire polished Nichrome 80 . 75 ohm be with the noisy cricket?
Absolutely.Could you do on set of aliens with a 316L wrap and the other just with the nichrome80 wrap
Cool. I just speced out a framed staple for the NC. 4x0.3mm ribbon, 28 gauge frames, 36 gauge binding, all kanthal. 8 wraps (both legs going in opposite directions), 2.5mm inside diameter. It should register around 0.48Ω as a SINGLE coil. Estimating it will pull about 17-18 amps on a couple of fully charge batteries. Run it lengthwise through the Velocity.An I guess I'll get the framed staples because I've heard awesome things about them as long as they'll fit the AugVape Boreas.
That'll work.An get the single polished niche one 80 for the noisy cricket.
High gauge Aliens and Fused Claptons.What other coils do you make that your recommend for the noises cricket?
Aw, shucks... Thanks!PS I've heard the best things of your coils!!!
It intrigued me too.. I was gonna buy a different dual 18650 mech but when i walked into the shop they told me he'd give me the NC for $20.. Needless to say it the cricket hopped into my pocket.. From what i was told its best to build above .5Ω. Also they said that the NC requires a shitload of maintenance, like almost daily cleaning of the contacts. However when i got home and got it all built it was pretty fuckin cool.. I guess it depends on the build n atty, but i didnt get great flavor on a dual 24g 12 wrap NI in the indestructible rda... Though the clouds were dense and voluptuous.. Its not any everyday mod for me but its fun to use for an hour or so while i walk my dog or do paperwork. If your intrigued, cautious, and arent goin to mind a little extra maintenance then go for it.. Its a fun toy to add to your collection and at the price you cant afford to pass it upThe noisy cricket has me intrigued.
I think I'll get one and new batteries.
What battery do you recommend using in it?
Ohhh.. And im using green samsung batteries with no issues..The noisy cricket has me intrigued.
I think I'll get one and new batteries.
What battery do you recommend using in it?
Just like @Vape7od uses, I highly recommend the Samsung 25Rs from liionwholesale.com.What battery do you recommend using in it?
Try it with a set of kanthal and/or nichrome fused Clapton coils. You'll be amazed at the difference!I guess it depends on the build n atty, but i didnt get great flavor on a dual 24g 12 wrap NI in the indestructible rda...
Build above 0.4 ohmsThanks guys, ordered an indestructible atty, NC, and samsung batteries, I'll let you know how I go.
I have some alien wire, 0.3 0.8 - 32g, and 26/32 clapton to try in it.
Yeah I just put an order in on 3fvape for a heat sink for this very reason... well and picked up a few other goodies
Just get a FDV kit for itYes, this is common for questionable rda pins and I grabbed one from 3fvape just for that reason.
Sent from my shoe phone using Tapa Toe Pro
I'm not sure why I had such problems with it, but I killed the buttons quick. My favorite vape on it was my dark horse with some 3mm Claptons. Want to get another series mech now but obviously need something with a better button arrangement.Yeah, they're not for everybody. I bought a few when ecig had them for 5 bucks, and judging on how long my first two have lasted (are lasting), I'm set for life.
Check out the vcp piglet, just a tad pricyer lol... but it's a damn nice series mod and worth it, not much to ware out on that one. I have 2. Button is always nice on that one!I'm not sure why I had such problems with it, but I killed the buttons quick. My favorite vape on it was my dark horse with some 3mm Claptons. Want to get another series mech now but obviously need something with a better button arrangement.