Become a Patron!
Armageddon Mfg. Squonk
- Thread starter Don29palms
- Start date
Going to set a friend up with one of the boxes and an RDA. He doesn't squonk yet, but he will .
The rest are all mine!
Nice doors.
Where did you get them?
They were on sale at armageddonmfg for 5 bucks but once the word got out they went fast.
They are V1 doors but with a little sanding they fit V2 and V3
Sent from a Galaxy far far away!
Yes, the bottle side.
I put the sandpaper on a flat surface and sanded the edge until it would fit slightly snug, you will need to round the corners and on the side you didn't sand you'll probably need to sand them down slightly as well.
Pretty easy.
Sent from a Galaxy far far away!
I'm jealous as hell of all the ones i see popping up with those green doors haha.I seen a few on the site one day,then when i went back all the green were gone.Beautiful pieces though.
You can run this one either way, you'll get less arch with it the recommended way. Tube mechs with venting are where I pay extra attention to the orientation.
No you won't create a dangerous situation
thanx. other than the arching, thats what i figured.
Yeah, and the arching is only in some depending on how the battery contacts are designed.
I agree.I hesitated on even getting one because they are plastic,but after getting mine and using it for just a few hours,i had to go and buy another.
Beautiful!
Is that the Axial without the beauty ring?
Mine came today! I ordered 2 doors but they called to say they couldn't give me the doors. He offered me two doors made for the version I had ordered. He ended up sending 3! Not quite as cool as the other doors but I'm happy. Now to pick out a rda and fire it up!
They’re really nice!
In the past when one of my magnets would fall off I used crazy glue.
Vape Fan
_evil twin_
Staff member
Senior Moderator
VU Donator
Platinum Contributor
Press Corps
Member For 5 Years
did you do this yet ?
Not yet. The rectangular magnets are too big. Plus I have to get crazy glue
Not yet. The rectangular magnets are too big. Plus I have to get crazy glue
so, they came with magnets, that are not installed ?
perhaps they are press fit, me thinks.
but, you must be very carefull installing them = get 1 backwards = ouch.
Yeah that sucks after it's been glued in.
How’d you do that?
i have a flannel jammy type pants on . i just took the mod and ran it up and down a bit on each side.
make sure they are clean, no Cheeto's or boogers or ............
Lol! Simple techniquei have a flannel jammy type pants on . i just took the mod and ran it up and down a bit on each side.
make sure they are clean, no Cheeto's or boogers or ............
The blue door matches the drip tip and looks cool with that battery wrap. Should I say more about the blue door or is this some kind of inside joke?
I thought it was black.
Oops, twenty pictures up, there is a blue-ish one. Looks good with the wraps.
Couldn’t see it too well, I thought it was the reflection tinting it slightly bluenobody says nuthin about the blue door ?
nadalama
Senior Moderator
Staff member
Senior Moderator
VU Donator
Diamond Contributor
Member For 4 Years
VU Patreon
I love the blue door. If I had ordered one, that's the color I would have picked.
Looks badass. I might have to give it a whirl cause I like yours better than my frosted ones for surenobody says nuthin about the blue door ?
I sanded and polished my frosted clear door.
It looks good but there is something odd around the bottom magnet. I don't know if it's glue or a reaction from the glue.
may i be honest ?
also.
that bottom magnet. mine doesn't have that, so i am thinking its not the glue. i am thinking that when they milled it something not good happened. of course, i could be wrong.
