This is what I'm trying to explain.... If you have plenty of money buy a 80 watt mod..... Later you will see a tank that you like but it's a subohm tank with coils that are .25 ohms.... This tank will require 80 to 100 watts to get flavor and clouds.....
Just like raymo advised me, put your coils 3mm from the build deck vertically, and as far out as you can get them. Dramatic improvement in flavor.
Cause you know it's so similar in size to a small mod like a cov mini volt or a single 18650 ipv d2/3. And it definitely weighs less than a cuboid
2 wrapPutting a set of these in the Boreas tomorrow for testing
SPECS: 10 x .4R/26N80/38N80/48N80
View attachment 53098 View attachment 53096 View attachment 53097 View attachment 53099
Just about 4-5 Wraps....Im not planning on using as much Ribbon or the same exact sizes but the end result will look the same.
Nice coil I made some alien with 316 stainless ohming at .13 for the set.... Push the bottom on 80 watts instant fire red.......
It takes time practice and some patience...but if your not doing it for fun then it may not be for you...I get frustrated sometimes but after awhile you get a feeling of zen making them...and then you think about it all damn day...then you drive everyone around you nuts by showing off "what you made today"
One step at a time...Ive been building for a year and I started doing more then Fused Claptons and Staples a couple months ago, there isnt a reason to rush so just take it easy and celebrate your every milestone
Now that is even above my skill set...well done
One step at a time...Ive been building for a year and I started doing more then Fused Claptons and Staples a couple months ago, there isnt a reason to rush so just take it easy and celebrate your every milestone
Now that is even above my skill set...well done
There are many of us on the forum check out the thread where most of us chit chat and post our builds: LINK
There are many of us on the forum check out the thread where most of us chit chat and post our builds: LINK
If you go on Instagram you will see there are thousands and thousands of builders and most of them make just about everything that Ive made look like Juicy's coil
I only cited your coil because of the amount of intense concentration and craftsmanship involved, I was merely pointing out how well your coil was made, like a fine swiss watch
Clean build....Im not sure how I feel about the doors layout but the internals look solid
I refuse to believe that! Your shit is fucking BEAUTIFUL! ^.^There are many of us on the forum check out the thread where most of us chit chat and post our builds: LINK
If you go on Instagram you will see there are thousands and thousands of builders and most of them make just about everything that Ive made look like Juicy's coil
I only cited your coil because of the amount of intense concentration and craftsmanship involved, I was merely pointing out how well your coil was made, like a fine swisswatchcheese
This is the primary reason I build stuff. I really don't need to, I have access to a lot of wire types, but it's a zen thing after a while, as long as it isn't going to hell..plus I like experimenting on new stuff. That's why I've been doing all the braids, it's more orderly and doesn't require power drillsIt takes time practice and some patience...but if your not doing it for fun then it may not be for you...I get frustrated sometimes but after awhile you get a feeling of zen making them...and then you think about it all damn day...then you drive everyone around you nuts by showing off "what you made today"
I prick myself all the time stick and the worst yet is getting a piece of Ribbon wire under your fingernails...or leaving a Staggered Fused clapton clipping on the floor and accidentally step on it in the middle of the night and then it bend almost 90 degrees INSIDE of your big toe...then you have to pull it out some then turn it and pull it out more...
it's just another layer to this hobby / job for me. I don't pretend to be an expert at it but I'm happy with the more intricate stuff I've made, and more importantly, I had more fun making it than I do vaping on it. If that isn't the case for people wanting to do the complex builds, they're gonna get real frustrated haha
I dont even vape half the builds I make anymore....I just mount them and take pics, heat them up for colors and then take more pics and then add it to the coil graveyard and make something different...I love buildingThis is the primary reason I build stuff. I really don't need to, I have access to a lot of wire types, but it's a zen thing after a while, as long as it isn't going to hell..plus I like experimenting on new stuff. That's why I've been doing all the braids, it's more orderly and doesn't require power drills
Sent from my SM-G935V using Tapatalk
Most of the braids I haven't vaped on. But I vape on the aliens and staples. And a couple of the braids are actually really good
