voltage

I have 4 istick pico devices, all are fairly old. Two of the devices draw the way I want but the other two are difficult and require deeper inhale. I have moved a battery and tank between the four and the 'v' setting on the two that require a deeper inhale show 0 whereas the two that I like...

I went on this page https://www.steam-engine.org/modrange.html and what I got from it is that the max voltage for my mod is limiting my wattage? I am using the Eleaf iStick TC100W, which actually goes to 120W. The coil I am using can go to 160W. But my mod limits me to 75W. What is the problem...

Really lost with first 2 battery mech! I picked up a Noisy Cricket on a whim and have no clue how to figure my voltage and current for a series circuit. I am using 2 35A 3000 mAh 3.7v(4.2v on full charge) IMR18650 batteries. Does my voltage double in series? And what happens to the discharge...

I have a voopoo drag with the gene chip in it. I recently purchased a rda and a kit along with wire and cotton. I have researched ohm law and looked at coil building calculators. I have two 18650 batteries with 20 continuous and 30 pulse amps. they are both 3.7 volts. I'm confused as to since i...

I’ve been vaping for a couple years now and have decided to get into mech mods. I’m doing my research on Ohm’s Law to being but I’m a bit confused by the Voltage Input part. When I’m calculating my amp draw do I use the 4.2V that my battery outputs raw, or do I use the 3.2V that I get after...

Hello all! Does anyone have any recommendations to check battery voltage thats portable to carry around and accurate? I am using a mech mod so it would be nice to know if theres any inline voltage meter thats accurate. I was thinking of something like this...

Ok guys, so i know how steam engine works. All i wonder is, will more voltage take more power of the battery or amps? My build right now is .18 ohm and it sucks out the batteries. Its a 4 battery mod guys, so i have a capacity of atleast 16 volts and 80 amps.

I went and bought the Wismec Reuleaux RX200S with the Griffin 25 RTA tank. I built dual coils with 26 ga SS 316L using my fancy new coil master, .40 ohms. I'm still not 100% sure how my watts and voltage should be set.

Hello everyone! I just received my Kangertech Subox mini. been play around with it for few hours and feels great! My friend just help me build a coil for the RBA and it reads 0.7ohm and I'm vaping at 25W. The voltage was displayed as 4.3V. Is it safe to vape at 25W on the 0.7ohm coil? My...

i have a Joyetech eVic-VT (not mini) with the tank that comes with it. My atomizer is at 1.09 ohm

Please stay the hell out of this thread if all you want to do is argue and spread misinformation. I created this thread about PWM and not about batteries or anything else. This is thread made to help people understand PWM, not a place for you to measure your dick in public. This thread was made...

In need of serious help before I say f*** all of this and go back to cigarettes. I have the Sigelei 90w plus mod with a single 26550 / 4200mAh / 40A / 3.7V battery. It came with an Ares tank, which I liked for it's simplicity. But as they don't make it anymore, I did some research and ordered...

Hi guys! Long time since i have had a question here Im thinking of buying the Wismec Reuleaux rx 300 and tfv12 atomizer. I currently have some 3.6V batteries I know how to apply new cotton and such, but how do i get a proper wire for my build? I want to use the dual coil or triple coil deck...

It seems that the DNA 200 board in my LAVABOX is discharging Cell 3 (likely an issue with the charging section). Any LiPo I put in her (the 900 mAh and two different 1,300 mAh) has cell 3 down to ~3.7V after 3-4 days while cells 1 and 2 are still at 4.18. Since I'm past the manufacturer's 90 day...

The voltage was stable for a while around 4.50 ish at 60W and one day it just jumped up to around 7.00v and now if I draw too long on it I get burnt taste and it gets hot. I can't figure out what the problem is. I tried modifying my coils to get rid of the crap taste but it didn't help. Any...

I am going to try and build a "Super Vape" and can't decide weather I should have .01 ohms @ 1232.1 watts (11.1V) or 1.2 ohms @ 940.8 (33.6V). Should I go high voltage for power? Or go subohm with high watts?

So I'm looking to use a Turnigy 2.2 (2200mAh, 20C, 44 M.C.D., 11.1V) 3s Lipo to power a DNA 200 chip with a .2 ohm coiled tank. 11.1V /.2 Ohms = an actual discharge of 55 Amps, which exceeds my maximum discharge rating of 44 amps. Does the DNA 200 automatically protect itself? I know that I...

First and foremost, I apologize if there is a previous thread explaining this well. I understand how electronic cigarettes work, and i've familiarized myself with each part. I just can't seem to understand the relationship between Ohms, Amps, Watts, and Volts. I recently ordered some parts from...

Hi guys, First post. I got a Kangertech subox mini, just fixed up my RBA with these specs: 0.3ohm using 26ga Nichrome, 7 coils 22W (i feel is the optimal taste for my juice) 2.5V discharge (as seen on the OLED display) Please correct me if wrong-> I suppose Amphere drawn is about 8A (V/R)...

I literally just bought the newly released kbox mini platinum. I got my subtank separately a while ago which I love but I always kind of regretted not buying one of the subox white or black starter kit versions. Anyway my Istick has served me well, but seeing as it was after Christmas I thought...

I literally just bought the newly released kbox mini platinum. I got my subtank separately a while ago which I love but I always kind of regretted not buying one of the subox white or black starter kit versions. Anyway my Istick has served me well, but seeing as it was after Christmas I thought...

Hello so I recently purchased an iPV D2. I had built a .35-4 ohm coil and I'm using 18650 batteries of course. It does not allow me to vape over 30w, maybe I can get away with 32watts but then it tells me "Check battery" indicating the voltage is more than 3.6. So from what I'm understanding I...