ohms

Well i have box switcher by vapoersso and manta RTA , 2 samsung 25R , 2 coils fused clapton ( 0.20 togther ) well i have wanted to clean up my tank with some warm water so i did i cleaned up everything and i wish i never did :-( it have been week or two since and my Ohms keep changing every...

I have a wismec Machina and a wismec luxotic nc, now they both came with 2 .28 caption coils I installed it on the Machina and it worked fine, I bought a bunch if different coils pre-made cause I'm not into building just yet. so I have installed .45 twisted coils in it and it hits like shit...

I have a battlestar smoant 80w uses one 18650 battery This is a second post im doing from another one I made just so I can get some different opinions on this so I know what to get. What ohm range should I aim for for a 80w regulated device using a single 18650 battery if I go to the store...

Today i built my first clapton coils since i thought that those coils can be interesting to use/try. I was using parallel kanthal coils for a while and i have never used those more "complicated" wires ever before. i was calculating how much wraps should i do so my ohms will be somewhere around...

Disclaimer: Please no one try what I'm about to describe. While it may be listed as safe on a website, I know enough to know that this is pushing the limits much further than they need be pushed. I just don't want to get anyone killed... Hey guys, Quick question for anyone who may happen to...

I need help :( I am not very educated in the vaping world, I mainly just started them as a less stinky & better tasting alternative to cigarettes. I've been using smaller vape pens for years now and decided to take the plunge and get a bigger vape so that I don't have to charge it multiple times...

Hey everyone! I read this forum from time to time but I just signed up. I apologize if a problem like this has already been covered. I can’t find a way to search the forum from my phone. I’ve been vaping for a couple years now and I’ve never had a problem solving any issue I’ve run...

My ohms is .12 requiring 35 amps. My mod takes two 18650s I have samsung 25r 2500mah 20amp. With both of these in my mod is it safely giving 35 amps?

Hey,i have a SMOK MAG with a DROP rda with 2 alien clapton coil,those came to 0.11 ohm,im pretty new at vaping and just dont want to burn my face,what is a decent wattage for that setting because im having problems finding out!!!

hello I’ve recently bought an rda and am planning on getting a coil building kit, but I have no clue what an ohm reader does, I know it tells you the ohms but why do you need that, and I plan on putting my rda on a smok t-priv until I get a mech mod, so any and all information on ohm readers...

I am a YouTube reviewer.... I reviewed the dead rabbit.... it was once great. But today it jumps ohms when I fire my mod. It's the only RDA that does it. I changed my coils like three times, two different brands and I fully, and I mean fully disassembled it, cleaned it. I changed the grub...

I’ve been vaping for a couple years now and have decided to get into mech mods. I’m doing my research on Ohm’s Law to being but I’m a bit confused by the Voltage Input part. When I’m calculating my amp draw do I use the 4.2V that my battery outputs raw, or do I use the 3.2V that I get after...

I went and bought the Wismec Reuleaux RX200S with the Griffin 25 RTA tank. I built dual coils with 26 ga SS 316L using my fancy new coil master, .40 ohms. I'm still not 100% sure how my watts and voltage should be set.

I've tried reading many battery articles across the web, and see stuff like continuous capacity, amps, capacity, safety, etc. But I don't feel like I really understand it in practice. So I'll just come out and ask: I'm using two Samsung 25r batteries in a Predator mod. I use an RTA with...

This morning, as if Satan himself escaped my dreams, my mod started making HUGE jumps in ohms. Worked fine last night around .55ohms (a .4 coil, people on here told me not to worry about that if it performed well, which it did, up until this morning!). Now, it jumps anywhere from .6 on one click...

In need of serious help before I say f*** all of this and go back to cigarettes. I have the Sigelei 90w plus mod with a single 26550 / 4200mAh / 40A / 3.7V battery. It came with an Ares tank, which I liked for it's simplicity. But as they don't make it anymore, I did some research and ordered...

Hello, I have a 3 battery regulated mod (Smok Koopor Primus 300W) with TFV8 RBA section. I'm going to use 2 coils in the RBA. The resistance of one coil is 0.23 ohms so two coils will give 0.11 ohms. I'll be using 3 Samsung 25INR 20a batteries with this build. Battery specs are...

Recently got a Smok Osub 80w off a friend, and bought a new coil with it, the Brit Beast baby .4 ohm, but ive just been having trouble getting the vape to reach the correct # of ohms. I know that the vape should be able to reach 0.4 ohms but it does not let me go past 0.218 ohms. What do I do...

hey folks this is my 1st post and I've a couple of questions I wanna clear up. I'm not working at the moment for health reasons (hopefully that changes soon), so I want to make my vaping as cheap as possible. I have an aspire NX30 rover kit which unsurprisingly goes to 30w, I don't know the amp...

I'm struggling to get to .25ohms no matter what I do. All my builds end up at the .15 range and per ohms law I should be no lower than .17 but I'd like to be closer to .25ohms myself. I have 24g stainless steel and kanthal as well as 22g stainless steel and I'm not sure what to do. Is there a...

So there isn't really any problem with my alien I am just confused with it, I used to have a fuchai 200w and every time you would fire it the ohms would change if they had to of course and not by much. But with my alien. The ohms will always stay at let's say .255ohms untill I unscrew my rda and...

Hey guys, I'm using a Vaporesso Target Pro with stainless ccell ceramic coils at .6 ohms. They are rated for 40-75w. Is it ok to run them at a wattage lower than 40 or will this hurt the coil? Cheers

What ohm range do YOU favor for flavor on your mech mod?

I've been trying to look at various charts to determine appropriate coil builds and wattage settings. So far I'm only confused by it so hopefully someone can help straighten me out. Many voltage/ohm charts are like this one linked off Phil Busardo's site...

I just built my first coil in my cubis RBA it is reading at 1.30 ohms I used 26 gauge wire I think 7 or 8 wraps. I am getting a great vape at 40 watts/7.21 volts. Is this ok or am I running it to high?

Hi all, new to vaping and 'vaping underground'. So a real noob! Background: interested in vaping and bought a Kamery k1000 epipe as an easy first vape experience. It tooks weeks for me to receive the pipe and I got a bit excited by the steel punk slug (18650 full mech mod) and bought one online...

So I'm looking to use a Turnigy 2.2 (2200mAh, 20C, 44 M.C.D., 11.1V) 3s Lipo to power a DNA 200 chip with a .2 ohm coiled tank. 11.1V /.2 Ohms = an actual discharge of 55 Amps, which exceeds my maximum discharge rating of 44 amps. Does the DNA 200 automatically protect itself? I know that I...

My setup I have the bothering question about is an IPV3 Li with a Lush RDA. I am running a dual coil setup of twisted 22g Kanthal. Both coils have 5 wraps and two half wraps to make the wrap count an even 6 per coil. When I screw my RDA into my box mod they read between .09-1.3ohms. Each time I...

First and foremost, I apologize if there is a previous thread explaining this well. I understand how electronic cigarettes work, and i've familiarized myself with each part. I just can't seem to understand the relationship between Ohms, Amps, Watts, and Volts. I recently ordered some parts from...

so more or less i wanna start cloud chasing. i want to learn how to build a subbohm worthy mod out of what i have. i'm from the philippines btw. so i need help. here is what ive got. ive got the chi you mod (original) with a buhawi RDA. any suggestions on how i can build it to cloud chase? ive...

Hey everyone, I am knew to mods. I have used pens and a simple mech mod but just upgraded to a Sigelei Fuchai 200w. I am also using a Orchid RBA. I am not too knowledgeable on the tank, just that it is a dual coil and is showing .8 ohms. I am using these INR18650 batteries...

im relatively new to vaping, i have a uwell dual .5 coil. My ohms read .23 on my 150. Again, im new and im sure this sounds like a stupid question to some of you, but isnt it suppose to be at .5 ohms by default? I dont know how to caibrate resistance or if i can. But just curious why my coils...

So I'm a nooby, I apologise in advance as my terminology will probably be all off. I purchased the E-leaf Istick 100watt and I'm planning on a dual tiger coil build in a tugboat RDA. However I feel the batteries I bought may not be safe, I NEED HELP. The batteries are 18650 li ion and have...

Hey guys! I'm fairly new to vaping, i have an Evic Vtc Mini mod and a clone Velocity Mini. I'm using samsung batteries (smurf and grinch). I'm vaping a dual clapton coil on my velocity mini, reading 0.20 ohms and 13.0-13.5 amps on 36watts on my Evic. I have 3 questions: 1) I read that smurfs...

Hey guys! I'm still fairly new to the vaping world. Although im quite eductated on basics, s uch as juices, RDA's, mod types, etc. the advanced things are still confusing. However, that's not why I'm here. My best friend gave me his IPV Mini II box mod and another friend just gave me a Mad...

Hey guys! I'm still fairly new to the vaping world. Although im quite eductated on basics, s uch as juices, RDA's, mod types, etc. the advanced things are still confusing. However, that's not why I'm here. My best friend gave me his IPV Mini II box mod and another friend just gave me a Mad...

I'm incredibly new (like, minty fresh new) to dripping so I only have a brief understanding of ohms law and rebuildables. I wanted to know: - What impact on my vaping experience do different ohm builds (above ohm vs sub ohm and their high-low extremes) have on a regulated mod? - A lot of people...

hey guys, so Im rather new to coil building but I just built my first dual coil build in a dark horse. Im using an IPV4S and two Efest IMR18650 2500mAh batteries. Im pretty sure the wire is 24 gauge as well. My box tells me its running at .13 ohms and 2.54v at 50 watts. Im just wondering if this...

I just started dripping last week. I bought a Troll RDA, which I read was a very good beginner's Dripper tip. I use the Aspire Pegasus mod. When I bought my Troll, the guy who sold it to me at my shop walked me through my first build, ended up at about .35 ohms give or take. The he didn't real...

So i just bought myself a Troll RDA, which I am in love with, and just started making my own coils. I am currently using Kanthal-A1 at 24 Gauge as a Dual coil with about 8 wraps each, after doing the coils my Pegasus mod reads out .35 ohms. I was wondering would it be feasible to use 32 gauge to...

Ive got a subtank mini and was going to twist 2 bits of 28g kanthal together. How would i make this about 1.5ohms? Cheers

Hey everyone, New to the site, pretty new to vaping in general, and very new to coil building and drip tanks (built my first coils yesterday). So right now I'm working on upgrading from what I have set up. Though I am very satisfied with the amount of clouds I am getting and how good the flavor...

I only have 32gauge kanthal. Was thinking of grabbing 2 or 3 bits and twisting it then doubling it over and wrapping woth the 32. Would i run into any issues here? Would it be possible to get up near 1 ohm this way? Thanks.